Apps & launchersReviewed
Replace Google Maps on the AI Box Home Screen
Swap Google Maps for Waze or another navigator on the AI box home screen: set both Carlinkit navigation entries, or use the Picasou 3 Pro widget menu.
Carlinkit TBox PlusCarlinkit TBox AmbientCarlinkit TBox UHDCarlinkit TBox UltraCarlinkit TBox Ultra 2Ottocast Picasou 3 Pro
Quick answer
On a Carlinkit TBox, Google Maps leaves the home-screen map pane only when you pick your navigator in both entries under Settings → Display → Navigation settings: the navigation app and the launcher navigation widget. Three owners confirmed this. On the Ottocast Picasou 3 Pro, use the left widget's three-dot menu, updating firmware if your app is missing.
Before you start
- Your navigation app (Waze, a regional map app or another navigator) installed on the box and opened once
- The stock launcher as the default home app; a third-party launcher has its own map settings
- For the Picasou 3 Pro firmware step: stable power and the box's official update
Time: about 15 minutes.
Applies to
- Devices
- Connection to the car
- CarPlay and Android Auto
- Highest risk on this page
- Advanced
What this guide covers
Out of the box, the stock launcher on Carlinkit TBox units shows Google Maps in the large pane on the left of the home screen, and the Ottocast Picasou 3 Pro shows it in the navigation widget on the left. New owners ask how to change that almost every month, usually because they drive with Waze, a regional map app or another navigator.
This guide changes which app fills that pane and which app the box treats as its navigation app. It is a settings change on Carlinkit boxes, so the main route is Low risk. The page carries an Advanced label only because of one optional step for the Picasou 3 Pro: a firmware update, needed when your app is missing from the widget’s list.
If you use a third-party launcher instead of the stock one, the settings below do not apply to its home screen; that launcher has its own map and widget settings. To go back to the stock launcher, choose it under Settings → Apps → Default apps → Home app, as described in set the stock launcher.
Why two settings on Carlinkit boxes?
Carlinkit boxes split the job across two entries in the same menu, and owners who changed only one of them saw nothing happen.
- Navigation app sets the system’s default navigator. The box uses it whenever it needs “the” navigation app, and it decides which app’s voice goes to the car’s navigation channel while nothing else plays from the box. One owner summed it up: the navigator you choose there becomes the main one.
- Launcher navigation widget sets what appears in the map pane on the stock home screen. Changing this entry is what replaces Google Maps on the home screen.
A new owner who changed the navigation app alone still had Google Maps on the home screen; once told there were two options and setting both, it worked. Owners describe the menu under Settings → Display → Navigation settings on TBox Plus, Ambient and UHD builds, and as Settings → Navigation with two lines, each with an app picker, on TBox Ultra firmware. On a few older builds the second entry was elsewhere, so if you find only one line, look for a second navigation setting nearby.
The stock launcher also has more than one home layout. Owners mention a choice between two styles in the box’s own settings (the gear icon, not Android settings), and only the layout with the map pane shows the widget. If your home screen has no map pane at all, check the style first.
Before you choose: the trade-offs
Which app you put where has side effects. Read this before you set anything, so you only do it once.
Split screen. On many Carlinkit builds, an app that is placed in the home-screen widget does not appear in the split-screen list behind code 121212. A common setup is therefore to put a second maps app in the widget and keep your main navigator for split screen; split screen on Carlinkit explains the rule. One owner on a newer build found the opposite: his split preset kept opening the home widget until he set the navigator in both entries. Test split screen after the change if you use it.
Prompt sound. The navigation-app entry moves that app’s voice to the car’s navigation channel while the box plays nothing else. On many head units that is what you want: prompts dip the car’s radio instead of stopping it, as described in car radio goes silent when the AI box is plugged in. On a few head units the channel stayed silent and the prompts disappeared. If your prompts become silent, too quiet or too loud after this change, see navigation voice prompts too quiet, too loud or silent.
Voice search. Owners also reported navigation apps whose voice search or assistant misbehaved while the app was the box’s navigation app. A frequent recommendation in owner forums was to leave Google Maps as the navigation app and use your preferred navigator on its own. That costs you the home-screen pane for your navigator, so try your app in both entries first and step back only if something breaks.
Three setups owners use
Put together, these trade-offs leave three combinations. Start with the first and move down only when something does not work in your car.
| Setup | Navigation app entry | Widget entry | When it suits you |
|---|---|---|---|
| Navigator everywhere | Your navigator | Your navigator | You want it on the home screen and its prompts on the navigation channel. This is the confirmed route below. |
| Split-screen friendly | Your navigator | A second maps app | Your build hides the widget’s app from the 121212 split list and you want the navigator in a split. |
| Prompt-safe | Maps or another app | Your navigator | Prompts went silent with your navigator in the navigation-app entry, but you still want it on the home screen. |
None of them changes anything permanently: each entry can be switched back in seconds, so test one drive per setup rather than reading forum threads for hours.
Steps
Carlinkit TBox: choose your app in both navigation entries
- Low risk
- Time: 5 minutes
- Worked for 3 of 3 reports
- Install your navigation app and open it once so it can finish its first-run setup and get location permission.
- Open the box’s Settings → Display → Navigation settings. On TBox Ultra firmware, open Settings → Navigation.
- Tap the navigation-app entry and pick your app.
- Tap the launcher navigation-widget entry and pick the same app.
- Press Home and check the map pane on the left.
- Tap the pane and check that your app opens.
Three owners confirmed this. A new Carlinkit owner could not get Google Maps off the home screen after changing the navigation app; after being told there are two options and setting the second, it worked. A TBox Ultra owner on a firmware from early 2026 found the two lines with app pickers under Settings → Navigation, set both and had his navigator on the home screen. A third owner, whose split-screen preset kept opening the home widget instead of his apps, fixed it by assigning his navigator to both the navigation setting and the home-screen widget.
The pane may show a live map or only open the app when you tap it, depending on the app and firmware. Either way, the app you set is the one that starts from the home screen.
Ottocast Picasou 3 Pro: pick the app in the widget's menu
- Low risk
- Time: 2 minutes
- Worked for 1 of 1 report
- Go to the stock home screen.
- Tap the three-dot menu in the top corner of the left widget, the one for navigation.
- Choose the option to change the navigation app.
- Pick your navigation app from the list.
- Tap the widget and check that your app opens.
The Picasou 3 Pro home screen has three widgets: navigation on the left, then media and weather. A P3 Pro owner found the app picker in the navigation widget’s three-dot menu, and another Ottocast owner replied that he sets his own navigator in that widget and it works. The owner who asked saw only Google Maps and one other map app in the list, not his installed navigator; if that is your case, go to the next step.
Picasou 3 Pro: update the firmware if your app is missing
- Advanced
- Time: 30–45 minutes
- Worked for 1 of 1 report
Warranty warning: this uses developer or engineering access. Follow the undo steps afterwards; some sellers refuse warranty claims on units with debugging left enabled.
- Note the current firmware version in the box’s system settings.
- Connect the box to stable power, in the car with the engine running or from a good charger.
- Run the box’s official system update and install the latest build Ottocast offers for the Picasou 3 Pro.
- Wait for the restart without unplugging the box.
- Open the left widget’s three-dot menu again and pick your navigation app, which should now be listed.
A P3 Pro owner could not choose his navigator in the navigation widget: the list offered only Google Maps and a Chinese map app. After a firmware update his navigator appeared in the list, and tapping the widget now opens it directly, instead of him opening it from the app list every time. He did not name the build, so check that your box is on the current official one before assuming the widget is broken.
Verify it worked
Check these once, in the car, with the box connected the way you normally use it:
- Press Home: the left pane shows your navigation app, or opens it when tapped.
- Restart the box and check again. The setting should survive a restart; if the pane goes back to Google Maps, set both entries again and make sure the stock launcher is still the default home app.
- Start a route and listen to the first prompt. If it is silent, too quiet or too loud now, see navigation voice prompts too quiet, too loud or silent.
- Play the car’s own radio and wait for a prompt. If the radio now stops for every prompt, see car radio goes silent when the AI box is plugged in.
- If you use split screen, open your preset or build a new one with code 121212 and check your navigator is still offered.
Undo / rollback
On Carlinkit boxes, go back to the same menu (Settings → Display → Navigation settings, or Settings → Navigation on TBox Ultra) and set both entries back to Maps. Nothing else changes, and your apps and logins stay as they are. If you only want your navigator out of the home-screen pane, change the widget entry and leave the navigation-app entry alone.
On the Picasou 3 Pro, pick Google Maps again in the left widget’s three-dot menu. A firmware update is the only step in this guide that is not reversed from a menu; its undo steps are inside the step above.
Troubleshooting this guide
Google Maps is still on the home screen. You changed one entry, not both. Set the launcher navigation widget entry as well, then press Home. If it still shows Maps, restart the box once.
Your app is not in the picker. Make sure it is installed on the box itself, not only on your phone, and that you opened it once. On the Picasou 3 Pro, older firmware offered only a few map apps in the widget; update as in the last step.
Your navigator disappeared from the split-screen list. On many Carlinkit builds the widget’s app cannot also go into a split. Put a second maps app in the widget entry, or follow split screen on Carlinkit. On a newer build, one owner had the reverse problem until both entries pointed at the navigator.
A Google Maps window opens at every start. That is the box’s auto-start setting, not the home-screen pane. Find the auto-start (start-up app) menu in the box’s settings and set it to your navigator or to none. An owner of a 4 GB / 64 GB QCM6125 box whose Google Maps window stayed on screen at every start until tapped confirmed this fixed it.
You want to change the app shortcuts on the home screen, not the map. On the TBox Ultra, long-press a shortcut and pick another app; one owner confirmed it worked.
The home screen has no map pane. The stock launcher has another layout without it. Look for the style option in the box’s own settings (the gear icon) and pick the layout with the map pane.
Prompts went silent after the change. The navigation-app entry moved the voice to the navigation channel, and your head unit does not play it. Pick a different app in the navigation-app entry and keep your navigator in the widget only; the prompts guide has the details.
You want the steering-wheel voice button to open your navigator or assistant. That is a different setting, the digital assistant app: see assign your assistant to the voice button.
Nothing here matches your box. Note the model and firmware date from Settings → About and ask the manufacturer’s support (Carlinkit: [email protected]; Ottocast: [email protected]). The Carlinkit TBox Ultra page and Picasou 3 page collect the other fixes for those boxes.
What owners said
“I had the problem on the Picasou 3 Pro. […] In the navigation widget I couldn't choose [my navigation app] as default; there was Google and some other Chinese product. After the firmware update I can choose it.”
Owner, Ottocast Picasou 3 Pro, Jan 2026
“I put [my navigation app] in this widget! Everything works.”
Owner, Dec 2025
“Thanks, sorted it out. It turned out I had to assign [my navigation app] to both navigation and the home-page widget.”
Owner, Mar 2025
Quotes are translated where needed and shortened ([…]); names are removed. Full counts are in the evidence table below.
Questions owners ask
I changed the navigation app, so why is Google Maps still on the home screen?
Carlinkit boxes have two separate entries: the navigation app and the launcher's navigation widget. The map pane follows the widget entry. Set your app in both, then press Home.
Will my navigation app still go into split screen?
Depends on the firmware. On many builds an app chosen for the home-screen widget is missing from the 121212 split list, so owners put a second maps app in the widget. One owner on a newer build needed the navigator in both entries before his split preset opened correctly.
Does the navigation-app entry change how prompts sound?
Yes. It sends that app's voice to the car's navigation channel while nothing else plays from the box. If prompts become silent, too quiet or too loud afterwards, see the navigation prompts guide.
Can I use Waze or a regional map app?
Yes. Any navigation app installed on the box can be chosen in both entries. Install it from the app store and open it once first, so it is set up before you assign it.
Related fixes
- Split Screen on Carlinkit: Widgets vs Real SplitAdvanced
- Navigation Prompts Too Quiet, Loud or Silent: 13 Owner ReportsLow risk
- Voice Assistant Doesn't Hear You: 13 Owner ReportsLow risk
- Apps Missing From the Home Screen After a Factory ResetAdvanced
- AI Box Fills Only Part of the Silverado or Sierra ScreenLow risk
Did this work for you?
Tell us which fix worked (or didn't), with your box, firmware date and car. Reports are how fixes get confirmed and re-ranked.
Send a reportChangelog
- Last reviewed against new community reports:
- Confirmed by 7 community reports on Ottocast Picasou 3 Pro.
- Page updated:
"Confirmed" means a community member reported that the fix worked on their unit. We have not tested it on our own hardware. How we verify.
Evidence behind these counts (5 cases)
One row per case: a device, a symptom and a fix, merged from owner reports. An owner counts once per fix. Reports with no outcome yet are not counted. Forum and chat message references are kept on file but not published, to protect owners' privacy; public Reddit and YouTube sources are linked.
| Case | Confirmed on | Result | Source |
|---|---|---|---|
| case-8190 | Model not stated | 3 worked | Owner discussion threads, 20 messages |
| case-8191 | Model not stated | 1 worked | Owner discussion threads, 2 messages |
| case-8192 | Ottocast Picasou 3 Pro | 1 worked | Owner discussion threads, 5 messages |
| case-9420 | Model not stated | 1 worked | Owner discussion threads, 6 messages |
| case-9421 | Model not stated | 1 worked | Owner discussion threads, 3 messages |