Skip to content
AI Box Fix

TEYES head unitsReviewed

TEYES Cold Boots at Every Engine Start: Sleep Setting, SIM

TEYES head unit shows the logo and loads for up to a minute at every start? Set the head unit shutdown item to Sleep, then check the SIM. CC4 Pro, CC3 2K.

Illustration: TEYES CC4 Pro close-up in a car dashboard

Quick answer

On a TEYES head unit that cold boots at every engine start, open the factory settings, then the head unit shutdown item, and choose Sleep, not power off: that worked for 2 of 3 TEYES owners, one on a CC4 Pro. Where Sleep was already set, another SIM card, forced 3G or an update each cured one unit.

Symptoms

  • The TEYES logo and a 35 to 60 second load at every engine start, on a unit that used to be ready in 5 to 10 seconds
  • The unit starts from zero even after a ten-minute stop
  • The shutdown setting already reads Sleep, yet most starts are full boots
  • With the mobile network on LTE the unit seldom wakes from sleep; on 3G it always does
  • The cold boots began after the car battery was disconnected, or after a repair or an update of the unit

Applies to

Head unit
TEYES: CC4 Pro, CC3 2K, CC3
Setup
Phone → TEYES unit
Phone projection
CarPlay and Android Auto
Highest risk on this page
Advanced
Status
Workaround confirmed by the community

Why it happens

A TEYES unit is an Android computer. When the ignition goes off it does one of two things: it shuts down, or it goes to sleep with everything still loaded. From sleep it is ready in seconds; from off it shows the logo and loads for 35 seconds to a minute.

A cold boot also throws away the link to your phone. CarPlay or Android Auto has to be found and connected again after every start, so it comes up later than everything else on the screen (how to start CarPlay or Android Auto on a TEYES unit shows where that connection is made). No owner here tested a fix against a phone connection: every report measures the boot itself.

In the reports sleep fails for reasons that have nothing to do with each other: a shutdown item set to power off, a SIM card or the LTE network mode, and firmware that ignored the setting. Read what your unit is set to before you change anything. A unit that was already running and goes back to the logo while the starter turns has a different fault: TEYES reboots when you start the engine.

Where is the fault?

Run these checks in order. Each one clears one device, so you only work on the part that fails.

One test per device in the chain between the phone and the car screen
CheckTry thisWhat it tells you
Shutdown settingOpen the factory settings, then the head unit shutdown item, and read which choice is selected. Change nothing yet.Power off or reboot selected means the unit is doing what it was told: go to the first fix. Sleep already selected means the cause is further down this table.
Sleep itselfSwitch the ignition off, wait ten minutes, start the engine and watch for the logo. Do the same after the car has stood for two days.A logo after ten minutes means sleep is not holding. A full boot only after two days parked, or about once in 40 to 50 starts, is what one long-term owner still sees on a unit he considers cured.
SIM and mobile networkFor a day of starts, set the mobile network to forced 3G, or take the SIM card out.If the unit now wakes each time, the mobile side is what keeps it from sleeping: second and third fixes. One CC3 owner ran the 3G test; taking the card out follows from it and was not reported by anyone.
FirmwareOpen the unit's own update app and see whether a newer version is offered.One CC3 2K unit ignored its sleep setting until its owner took the offered update. No offer means the unit cannot fetch anything newer by itself.
Engine startSit with the ignition on and the unit running, then start the engine and watch the screen.A running unit that drops to the logo as the starter turns is restarting, not failing to sleep. Start with the page on reboots at engine start, in the related list.

Not sure what an AI box would add to an Android head unit? See AI box or Android head unit.

Fixes, ranked

Set the head unit shutdown item to Sleep

  • Advanced
  • Time: 5 minutes
  • Worked for 2 of 3 TEYES owners

Warranty warning: this uses developer or engineering access. Follow the undo steps afterwards; some sellers refuse warranty claims on units with debugging left enabled.

  1. Open the factory settings of the head unit.
  2. Open the head unit shutdown item.
  3. Choose Sleep. The other choice is called off by one owner and reboot by another.
  4. Leave the menu, switch the ignition off, wait ten minutes and start the engine. The unit should come on without the logo.

A CC4 Pro owner (12 GB / 256 GB) had a unit that was ready in 5 to 10 seconds until March 2026, then took about a minute at every start. It had been in for repair twice and had also been updated, and he could not tell which of the two changed it. Asked whether it was starting from zero or from sleep, he set sleep in place of off and wrote back that it helped.

A second owner, who did not name his model, found the same thing by himself: sleep has to be switched on in the factory settings. Since then his unit wakes at engine start and no longer switches on from nothing.

It did not hold for a third. His setting already read Sleep, and the cold boots, even after ten minutes away from the car, began after a workshop took the terminals off the battery. He removed Sleep, restarted, set it again and restarted: the next start was a wake-up, and only that one.

The item may not sit in the same place on every unit. One owner, whose question was a picture, wrote only that he had won and that it had been in the additional settings. He is not counted, because the reports do not record what he set there. The reports on this page give no code for the factory settings either; on TEYES external microphone ignored one owner reached that menu with the code 168. Change nothing else in it.

Replace the SIM card with a different one

  • Low risk
  • Time: 10 minutes, then several days of starts
  • Worked for 1 of 1 TEYES owner
  1. Take the SIM card out of the head unit.
  2. Fit a different SIM card, from another provider if you can borrow one.
  3. Use the car for several days and watch whether the unit now wakes from sleep at engine start.

This is the longest story in the reports. A CC3 2K owner (4 GB / 64 GB) had restarts at almost every switch-on from the day the unit was fitted. Over about four months he worked through dozens of tips: some gave a few normal wake-ups, others changed nothing. He gave up and got used to a 35 to 45 second load.

Later he changed the SIM for a card from another provider, for a reason that had nothing to do with the fault, and noticed that the unit had started waking from sleep. More than a year on it still does. A full boot comes only after two days parked or about once in 40 to 50 wake-ups.

He does not know whether the old card or its provider was the cause. The card was six to eight years old and had seldom been used, and he never put it back to find out. A SIM is not the only route to this fault: the third owner under the first fix never fitted one.

Force the mobile network to 3G

  • Low risk
  • Time: 5 minutes
  • Worked for 1 of 1 TEYES owner
  1. Open the mobile network settings of the head unit.
  2. Change the network mode from the recommended 4G to forced 3G.
  3. Use the car for a few days and watch whether the unit wakes from sleep at engine start.

A CC3 owner found this while looking for the opposite. He wanted a 4G-only mode; his network settings offered only “4G recommended” and “forced 3G”. On forced 3G sleep works on his unit, and so does the feature he calls no-kill. Left on LTE, sleep works “every other time”, which he corrects to practically never: the unit starts from zero.

It is a workaround with a price. He reports that 3G is sometimes too slow to carry his data, and where a provider has switched its 3G network off, this setting would leave the unit with no mobile data at all. He asked what makes LTE break sleep, and the reports hold no answer.

Set the delayed power-off to 10 seconds

  • Advanced
  • Time: 5 minutes
  • Worked for 1 of 2 TEYES owners

Warranty warning: this uses developer or engineering access. Follow the undo steps afterwards; some sellers refuse warranty claims on units with debugging left enabled.

  1. Find the delayed power-off setting of the head unit. The reports do not say which menu holds it; look beside the shutdown item of the first fix.
  2. Write down the value it has now, then set the delay to 10 seconds.
  3. Drive for a few days and count how often the unit still restarts at engine start.

A CC3L owner wrote that his unit, fine for the first two or three weeks, now restarted after every start. Another owner answered that a 10-second delay had helped on his own unit. He had not counted how often it still restarts, and added that once a day would not bother him. The CC3L owner has not reported a result yet.

For one owner it did nothing. His unit went fully off every time he started the engine, even when he had been sitting in the car with the radio on; he read about the delayed shutdown, set 10 seconds and saw no change at all. Nobody in the reports explains what the delay does on a unit that helps. The usual reading is that it keeps the unit on through the moment the starter turns, which is the subject of TEYES reboots when you start the engine.

One more report is close and is not counted. A CC3 owner with Sleep already selected had a restart every third to fifth start, on a battery reading 12.7 V at rest and 14 V with the engine running. He was answered with a picture of settings, wrote that it helped, and after several days had seen one or two restarts. The picture came without words, so which values he set is not on record.

Install the update the unit's own updater offers

  • Advanced
  • Time: Depends on the download
  • Worked for 1 of 1 TEYES owner

Warranty warning: this uses developer or engineering access. Follow the undo steps afterwards; some sellers refuse warranty claims on units with debugging left enabled.

  1. Connect the head unit to the internet and open its own update app.
  2. If a newer version is offered, install it and let the unit finish and restart by itself.
  3. Check that the shutdown setting still reads Sleep.
  4. Use the car for a few days and watch whether the unit wakes at ignition-on.

A CC3 2K owner with a Nissan X-Trail had a unit that powered down whenever the engine was off and booted from zero at every ignition-on, with sleep selected the whole time. In August 2024 he took the new version through the unit’s update app. Three days later he reported the unit in standby at every switch-on. He had changed no setting, lost no apps or settings in the update, and found the GPS noticeably better.

Others had pointed him at the wiring and the battery. His answer was that the wires have nothing to do with it, since the same car now sleeps as it should, and that he had no battery trouble. He gives no version number, so the report cannot tell you which release carried the change. Take an update only when the unit’s own app offers it.

Have the firmware installed again

  • Advanced
  • Time: An installer visit
  • Worked for 1 of 2 TEYES owners

Warranty warning: this uses developer or engineering access. Follow the undo steps afterwards; some sellers refuse warranty claims on units with debugging left enabled.

  1. Take any update the unit’s own updater offers first (the fix above).
  2. Ask the store you bought the unit from for the firmware of your exact unit and its instructions, or have the installer do the work.
  3. Expect to set the unit up again afterwards.
  4. Use the car for a few days and watch whether the unit wakes from sleep.

One owner, who did not name his model, answered the owner from the previous fix whose 10-second delay had done nothing: reflash it, it helped him. He had tried everything for a long time before that. He did not say where his firmware came from or how he installed it, so this page cannot tell you either, and it points to no file. A firmware file passed on by another owner is not a route this page recommends.

It failed for the CC3 2K owner of the second fix. His installer flashed new firmware after warning him that it was a 50/50 lottery that could leave a dead unit. Nothing changed, and a replacement unit behaved the same way. Weigh that warning before you ask for this.

Things to try (unverified on TEYES)

  • Cold boots with no cause found. The owner whose trouble began after the battery was disconnected asked whether anyone had met the same, and the reports hold no answer for him. The CC3 2K owner writes that many owners live with it, and that the advice he once followed was to stop chasing it. No TEYES owner reported a cause for these cases.
  • Check the unit’s power wiring. Two owners were asked about their wiring when they described cold boots. Neither reported a fault there: one was cured by the Sleep setting, the other by an update. No TEYES owner reported a wiring fault as the cause.
  • No mobile data after the unit wakes, until it is restarted. Owners raised this beside the cold boots. The reports hold no suggestion for it that a TEYES owner tried and reported on.
  • What AI box owners report. On an AI box, restarts mostly trace to a USB port that cannot power it (AI box keeps rebooting). That is another device with another power supply, and none of those reports is counted here.

If nothing works

Write down the family, the memory version and the firmware version, and the unit’s ID, which owners find under Settings → System. Add what the table above showed: what the shutdown item is set to, how long a cold boot takes, after how long a stop it happens, whether a SIM is fitted and on which network mode. Say what changed before it began: a disconnected battery, a repair, an update. How to report a bug lists what makes a report usable.

Send that to the store you bought the unit from; the regional store has a support page. A different unit is not a sure answer: one owner’s replacement cold booted exactly as the first had, and what cured his car was a SIM card.

If none of it helps, the honest position is the one the long-term CC3 2K owner describes: many owners live with it. The unit works, it takes most of a minute to get there, and the phone connects after that.

What owners said

“Thanks, it helped. I set it to sleep mode instead of off.”
Worked: Shutdown item set to Sleep
Owner, TEYES CC4 Pro, Apr 2026
“But changing the SIM card has solved this problem to this day.”
Worked: Different SIM card
Owner, Mar 2026
“The problem went away after I updated the unit to the new version through the update app. […] It updated, nothing was lost and everything works correctly! GPS also works noticeably better.”
Worked: Update from the unit's own updater
Owner, TEYES CC3 2K, Aug 2024

Quotes are translated where needed and shortened ([…]); names are removed. Full counts are in the evidence table below.

Questions owners ask

How long should a TEYES unit take to come on at engine start?

From sleep, seconds: a CC4 Pro owner counted 5 to 10 before his trouble began. A cold boot took about a minute on that CC4 Pro and 35 to 45 seconds on a CC3 2K.

Is an occasional full boot normal?

One long-term CC3 2K owner, on a unit he considers cured, still sees a full boot after two days parked or about once in 40 to 50 wake-ups. Another owner said a restart once a day would not bother him. A logo at every start, or after a ten-minute stop, is the fault this page is about.

Is the car battery to blame?

Not in these reports. Three owners with cold boots say the battery is healthy; one measured 12.7 V at rest and 14 V with the engine running. A unit that was running and restarts while the starter turns is another fault, covered on the related page about reboots at engine start.

Do I need a SIM card in the unit for sleep to work?

No. One owner whose unit cold boots never fitted one. The SIM side was the cause on two other units: one woke normally after a different card went in, one sleeps on 3G and not on LTE.

Did this work for you?

Tell us which fix worked (or didn't), with your box, firmware date and car. Reports are how fixes get confirmed and re-ranked.

Send a report

Changelog

  • Last reviewed against new community reports:
  • Confirmed by 7 community reports on TEYES CC4 Pro, TEYES head unit (model not stated), TEYES CC3 2K, TEYES CC3.
  • Page updated:

"Confirmed" means a community member reported that the fix worked on their unit. We have not tested it on our own hardware. How we verify.

Evidence behind these counts (6 cases)

One row per case: a device, a symptom and a fix, merged from owner reports. An owner counts once per fix. Reports with no outcome yet are not counted. Forum and chat message references are kept on file but not published, to protect owners' privacy; public Reddit and YouTube sources are linked.

CaseConfirmed onResultSource
case-1357TEYES CC4 Pro; TEYES head unit (model not stated)2 worked, 1 did notOwner reviews, 6 messages
case-1358TEYES head unit (model not stated)1 worked, 1 did notOwner reviews, 2 messages
case-1359TEYES CC3 2K1 workedOwner reviews, 3 messages
case-1360TEYES CC31 workedOwner reviews, 3 messages
case-1361TEYES CC3 2K1 workedOwner reviews, 2 messages
case-1362TEYES head unit (model not stated)1 worked, 1 did notOwner reviews, 2 messages