Skip to content
AI Box Fix

TEYES head unitsReviewed

TEYES CC3 2K Bluetooth Range Short: Firmware Setting, Its Risk

TEYES CC3 2K loses Bluetooth with the phone out of the car window? One owner cured it with one line in the firmware's config file. Brick risk: read first.

Illustration: TEYES CC3 2K in a car dashboard on a rainy evening

Quick answer

On a TEYES CC3 2K whose Bluetooth drops with the phone out of the car window, one owner changed the Bluetooth value in the firmware's config file from 7 to 0 and the range grew a lot (1 of 1 TEYES owners). The change needs a firmware install, and a failed install can leave a unit that does not start.

Symptoms

  • Bluetooth music breaks up or stops when the phone is held out of the car window
  • The Bluetooth link holds only while the phone stays inside the car, close to the head unit
  • You drive with the phone connected, switch the car off, and at the next start the unit has lost the Bluetooth connection

Applies to

Head unit
TEYES: CC3 2K
Setup
Phone → TEYES unit
Phone projection
CarPlay and Android Auto
Highest risk on this page
Brick risk
Status
Workaround confirmed by the community

Why it happens

Nobody in the reports established a cause. What they show is that the firmware of these units carries a text file of settings, and that one line in it says which kind of Bluetooth the unit is to use. A CC3 2K owner found the number 7 there, changed it to 0, and reported that his range grew a lot.

He took the change to mean that the unit had switched to its built-in Bluetooth module. That is his reading, and nobody confirmed or corrected it. A long-time community member’s note gives two values for the CC3, 7 and 1, depending on when the unit was made, and does not mention 0 at all.

This is not a setting in a menu. The line lives inside a firmware package, and the note that names it says it is set before the firmware is installed on the unit. A firmware install that goes wrong can leave a unit that does not start, which is why the fix below carries the highest risk label on this site and why the checks come before it.

Ordinary Bluetooth faults (a unit the phone cannot find, a connection with no sound) are settled without firmware: see TEYES Bluetooth: phone not found, no reconnect or no sound.

Where is the fault?

Run these checks in order. Each one clears one device, so you only work on the part that fails.

One test per device in the chain between the phone and the car screen
CheckTry thisWhat it tells you
Measure itPlay music from the phone over Bluetooth, carry the phone away from the car and note the distance at which the music breaks up. Repeat on another day.A link that fails with the phone barely outside the car, every time, is what the CC3 2K owner described. Write the distance down: it is the only way to tell later whether a change helped.
PhonePlay music from the same phone to a Bluetooth speaker or headset and carry the phone away from it.If that link also breaks up after a metre or two, the phone is the weak end and nothing on the unit needs changing.
A second phoneConnect another phone to the unit and repeat the walk.If the second phone holds the link much further, the unit's Bluetooth works and the first phone's pairing is what to redo. If both cut out at the same short distance, the unit is the common part.
PairingDelete the pairing on the phone and on the unit, pair again and repeat the walk.A normal range afterwards means the fault was in the saved pairing and you are done. No owner on this page said whether he tried this before he changed the firmware.
After parkingConnect the phone, switch the car off, come back after an hour, start the car and watch whether the phone reconnects by itself.A unit that has lost the connection each time is the second fault described under the fix. If the phone reconnects, that part of the page does not concern you.

Not sure what an AI box would add to an Android head unit? See AI box or Android head unit.

Fixes, ranked

Change the Bluetooth value in the firmware's config file from 7 to 0

  • Brick risk
  • Time: Set by the maker's install instructions
  • Worked for 1 of 1 TEYES owner

Warranty warning: this changes system partitions. A wrong file or an interrupted step can leave the box unbootable, and manufacturers treat it as outside warranty. Back up first and keep the undo steps open.

  1. Run the checks in the table above and write down the distance at which the link breaks.
  2. Try what costs nothing first: delete the pairing on both sides, or use the reset in the unit’s Bluetooth app, as described on TEYES Bluetooth: phone not found, no reconnect or no sound.
  3. Write down the family and memory version of the unit, its firmware version and the unit’s ID, which owners find under Settings → System, and when the unit was made or bought if you know it.
  4. Send those details to the store you bought the unit from, or to the maker’s support. Ask for the firmware package for your exact unit, for the instructions to install it, and for what the line sys.fyt.bluetooth_type in the package’s config.txt should read on your unit.
  5. Keep an untouched copy of the package. In a second copy, open config.txt in a plain text editor, find the line sys.fyt.bluetooth_type and write down the number it holds.
  6. Change that number, and nothing else in the file. The owner changed it from 7 to 0. If your line holds a number other than 7, or the line is not in the file, stop and ask support before going further.
  7. Install the changed package by the maker’s instructions, to the letter. This page gives no install steps, because no owner’s report gives them.
  8. When the unit is running again, pair the phone and repeat the walk from step 1.

What the owner reported. A CC3 2K owner wrote that his unit’s Bluetooth reception was poor: with the phone put out of the window, roughly speaking, the signal was lost and the music stopped playing properly. Three days later he had solved it. In the firmware’s config file he changed the Bluetooth value from 7 to 0, which he understood as switching to the built-in Bluetooth module, and the Bluetooth radius grew a lot compared with before.

What his report leaves out. He does not name the file or the line. He does not describe the install at all: where the firmware came from, which version it was, how it went onto the unit, or whether that erased his apps and settings. He gives no distance, before or after, and does not say whether calls or other Bluetooth devices behaved differently afterwards. He was the only owner to report this change with its values, so there is no second unit to compare with.

Where the file name and the line come from. They come from a long-time community member’s standing note for the CC3: if Bluetooth does not work, add a line to config.txt before installing the firmware, sys.fyt.bluetooth_type=7 for a CC3 made after March 2023 and sys.fyt.bluetooth_type=1 for one made before. That note is advice and not an owner’s result. It speaks of the CC3, not the CC3 2K, it speaks of adding the line, so the file may come without it, and it never mentions 0. The value 7 it gives for recent units is the value the CC3 2K owner found in his file.

A second owner who is not counted. An owner who did not name his unit connected his phone by Bluetooth, drove, switched the car off, and found at the next start that the unit had lost Bluetooth. He was told to experiment with the firmware and wrote back that the digit 0 had helped: the unit no longer loses Bluetooth. Neither message says which setting that 0 belongs to. It reads like the same line, and that is a guess, so the count above stays at one.

Where the package must come from. Take it only from the store you bought the unit from or from the maker’s support, made for your exact unit. A firmware file passed on by another owner is not a route this page recommends: nobody can tell you which unit it was built for or what was changed in it. For a sense of the stakes, an installer quoted on TEYES cold boots at every engine start called a firmware install a lottery that can leave a dead unit.

Things to try (unverified on TEYES)

  • Delete the pairing and pair again, or reset Bluetooth in the unit’s Bluetooth app. Both cured other Bluetooth faults for TEYES owners, with the counts on TEYES Bluetooth: phone not found, no reconnect or no sound. No TEYES owner reported that either widened a short range or stopped the connection being lost after parking.
  • Phones that lose the pairing after an update of the unit. Owners were told to pair the phone again, and none reported back.
  • Have the firmware installed again when Bluetooth does not work at all Brick risk. One owner wrote that he installed the firmware and Bluetooth started working. While looking for it he had found the download buttons inactive, and was told that the unit’s ID code has to be entered before anything can be downloaded. His messages give neither his family, nor his fault, nor the site, so he is not counted and no steps follow from him.
  • What AI box owners report. Pairing trouble on an AI box has causes of its own, and none of those reports is counted here: see phone won’t pair with the AI box.

If nothing works

If the checks point at the unit and you decide against the firmware route, living with it is a real choice. As the CC3 2K owner describes his fault, it showed with the phone outside the car.

Write down the family and memory version, the firmware version and the unit’s ID, the phone models you tried, and the distance at which each lost the link. Say whether the phone is forgotten after parking, and how long the car stood. How to report a bug lists what makes a report usable.

Send that to the store you bought the unit from; the regional store’s support page is the official route. A unit whose Bluetooth reaches no further than the dashboard on every phone is a warranty question for the seller. If firmware work is the answer, ask the seller to do it: an install the seller carries out is the seller’s to put right if it fails.

What owners said

“Solved the problem: in the firmware's config file I changed the Bluetooth value from 7 to 0. As I understand it, that switched to the built-in Bluetooth module, and the Bluetooth range grew a lot compared with before.”
Worked: Bluetooth value 7 to 0 in the config
Owner, TEYES CC3 2K, Dec 2024

Quotes are translated where needed and shortened ([…]); names are removed. Full counts are in the evidence table below.

Questions owners ask

Can changing this line damage the head unit?

The line is one number in a text file. The risk is the firmware install that applies it: an install that fails, is interrupted or uses a package made for another unit can leave a head unit that does not start. No owner in these reports described recovering from that.

What do the values 7, 1 and 0 mean?

The reports do not say. A long-time community member's note gives 7 for a CC3 made after March 2023 and 1 for an earlier one. The owner who set 0 understood it as switching to the built-in Bluetooth module, which is his own reading. Ask the maker's support what your unit should have.

Where do I get the firmware package?

From the store you bought the unit from, or the maker's support, for your exact unit. The owner who made the change did not say where his came from. This site does not host or link firmware, and a file passed on by another owner is not a route this page recommends.

Does the same change stop the phone being forgotten after every stop?

Possibly, and it is not counted. One owner whose unit lost Bluetooth each time he parked was told to experiment with the firmware and wrote that the digit 0 had helped. His message does not say which setting the 0 belongs to.

Did this work for you?

Tell us which fix worked (or didn't), with your box, firmware date and car. Reports are how fixes get confirmed and re-ranked.

Send a report

Changelog

  • Last reviewed against new community reports:
  • Confirmed by 1 community report on TEYES CC3 2K.
  • Page updated:

"Confirmed" means a community member reported that the fix worked on their unit. We have not tested it on our own hardware. How we verify.

Evidence behind these counts (1 case)

One row per case: a device, a symptom and a fix, merged from owner reports. An owner counts once per fix. Reports with no outcome yet are not counted. Forum and chat message references are kept on file but not published, to protect owners' privacy; public Reddit and YouTube sources are linked.

CaseConfirmed onResultSource
case-1559TEYES CC3 2K1 workedOwner reviews, 3 messages