Skip to content
AI Box Fix

Firmware & recoveryReviewed

TBox Keeps Rebooting and Wiping Itself When It Goes Online

A Carlinkit TBox that reboots and factory-resets itself every minute once online: keep it offline and install current firmware. TBox Plus.

Illustration: Carlinkit TBox Plus on a car's centre console at dusk

Quick answer

On a Carlinkit TBox that reboots and factory-resets itself every minute once it goes online, keep it off the internet and install the current official firmware with FOTA Local update: eight of ten owners who reported back ended the loop for good. If the box is already on the latest build, boot it offline and share internet a minute later.

Symptoms

  • A box that worked for years suddenly wipes itself and reboots every minute or two after it starts
  • The loop only happens once the box is online: pull the SIM and it stops, rejoin Wi-Fi and it returns
  • A factory-reset or data-wipe message flashes on each restart and you have to re-enter the Wi-Fi password
  • It began on its own in late May 2026, the same day for many owners, on older firmware
  • A plain factory reset does not stop the loop
  • Settings → About shows a 2023 or 2024 build and says there are no updates

Applies to

Devices
Connection to the car
CarPlay and Android Auto
Firmware in confirmed reports
Carlinkit TBox Plus: A13
Highest risk on this page
Advanced
Status
Fixed in firmware (2026-01-07)

Why it happens

Your box is a small Android computer, and it has a service that checks for and installs system updates over the internet. In late May 2026 boxes still on 2023–2024 firmware began to reboot and factory-reset themselves every minute or two, but only once they reached the internet over Wi-Fi or the SIM.

Owners narrowed it to that automatic online update. On these older builds the box pulls something from the update server at each boot that sends it into a reboot-and-wipe loop. Take the box offline and the loop stops; put the old firmware back online and it comes back.

Two ways out follow from that. Install a current official build and the fault is gone for good, even with the SIM back in. Or stop the box reaching the update — by turning the automatic update off, or by giving the box internet only after it has started — and the old firmware runs without looping. This is not the power or weak-cable reboot covered in AI box keeps rebooting; that one follows load, this one follows going online.

Fixes, ranked

Install current firmware with the box kept offline

  • Advanced
  • Time: 30 minutes
  • Worked for 8 of 10 reports

Warranty warning: this uses developer or engineering access. Follow the undo steps afterwards; some sellers refuse warranty claims on units with debugging left enabled.

  1. Start the box with no internet: remove the SIM and the microSD card and turn on airplane mode, so it stops looping long enough to work on.
  2. On a computer, download the current official firmware for your exact model and variant from Carlinkit’s own download page.
  3. Copy the file unchanged to the root of a FAT32 microSD card of 32 GB or less. Do not unzip it.
  4. Insert the card in the box, open FOTA Update → menu → Local update, pick the file, confirm the restart and wait for it to finish.
  5. Check Settings → About for the new build date, then put the SIM back.

Keep the box offline for the whole job: the loop only has to stay quiet long enough to copy the file and start the install. Owners who did this reported the box steady afterwards even with the SIM back in, one on a 3.5-year-old TBox Plus whose box had wiped itself that morning, another whose box had zeroed itself many times until the update to Android 13.

The full card-and-FOTA procedure, including what to do when the card is not seen or the install stops, is in update TBox firmware with FOTA; this page only adds the offline-first step. On a TBox Plus going from Android 12 to Android 13, one owner had to install the 1 Apr 2024 Android 12 build first, then the 7 Jan 2026 Android 13 build; a direct jump can fail. The firmware tracker lists the builds owners discuss.

Turn off the automatic system update and keep your firmware

  • Low risk
  • Time: 10 minutes
  • Worked for 2 of 2 reports
  1. Start the box with no SIM so the reboots stop, then connect it to a Wi-Fi hotspot and wait about ten minutes.
  2. Open Settings → More to reach the Android settings, scroll to About, and tap the build number 5 to 7 times to unlock developer options.
  3. Go back to developer options and turn off “automatically update system after reboot”.
  4. Restart the box a couple of times to confirm it stays up.

This keeps the box on its current firmware. One owner did exactly this and reported the box rebooting cleanly on purpose with no loop afterwards. A second owner followed the same steps and said it fixed his box after the card firmware update had failed for him.

The reset that already happened still clears your apps, so you set those up again, but you do not have to flash anything. If you would rather be rid of the fault for good, use the firmware update above instead.

Already on the latest build? Boot offline, then share internet

  • Low risk
  • Time: 5 minutes
  • Worked for 1 of 1 report
  1. Start the box with mobile data and Wi-Fi off so it boots without reaching the internet.
  2. Wait about a minute, until the launcher has fully loaded.
  3. Turn on your phone’s hotspot, or re-enable the SIM, so the box goes online only after it has settled.
  4. Optional: set a phone automation to switch the hotspot on a minute after the phone connects to the box, so this happens by itself each drive.

This is for a box already on the newest build, where re-flashing returns “Upgrade failed”. One owner on an Android 13 TBox Plus set that phone automation, then drove 150 km with a single reboot and none after. Giving the box internet only once it has settled keeps it clear of the trigger.

Things to try (unverified)

  • Wait a day before touching it. A few owners found the box working again the next day on its own, which points at a server-side part to the trigger. The box had still wiped itself, so you set it up again regardless, and nobody should count on this.
  • A plain factory reset. One owner tried a factory reset and the loop came straight back, so it is not a fix on its own. Use a reset only as part of an update, as a last step, not instead of one.
  • A box already on the last firmware that still loops. At least one owner of an original TBox on the latest build still had the loop with nothing left to update to. The offline-then-internet workaround above is the thing to try, and contacting support is the next step.

If nothing works

Collect what support needs before you write: the box model and firmware date from Settings → About, the car’s make, model, year and head unit, whether the SIM was in, and a short phone video of the loop.

Carlinkit’s firmware downloads and support contact are linked below. If the box is already on the newest build, cannot be re-flashed, and the offline workaround does not hold, ask support whether a corrected build exists for your exact model. Start here explains how the box families differ if replacement becomes the honest answer.

What owners said

“It kept doing this every minute after booting. Solution was to eject the SIM card, the microSD card and activate plane mode on the device. Then download the correct latest firmware from Carlinkit […] After this, no issues.”
Worked: Offline install of current Carlinkit firmware
Owner, Carlinkit TBox Plus, Jun 2026
“Drove 150 km today. Once the box rebooted in the loop pattern, and never again. The scheme works. […] Start it without internet or Wi-Fi, the box loads, a minute later share internet to it and enjoy.”
Worked: Boot offline, share internet a minute later
Owner, Carlinkit TBox Plus, May 2026
“Started the box without the SIM card (reboots stopped), joined my Wi-Fi hotspot, waited about 10 minutes, then in developer mode disabled automatic system updates after reboot. […] Rebooted it on purpose a couple of times: works correctly.”
Worked: Turn off automatic system update
Owner, May 2026

Quotes are translated where needed and shortened ([…]); names are removed. Full counts are in the evidence table below.

Questions owners ask

Why does removing the SIM stop the reboots?

With no SIM and no Wi-Fi the box never reaches the update server, so the loop that begins when it goes online does not start. It keeps the box up long enough to update it; on the old firmware the loop returns as soon as it is online again.

Does a plain factory reset fix it?

No. One owner reported the loop returning straight after a manual factory reset. Updating the firmware, or turning off the automatic system update, is what ended it.

Will I lose my apps?

The loop factory-resets the box itself, so apps and logins are usually gone by the time you fix it. Plan to set the box up again afterwards.

My box is already on the newest firmware and still loops. What now?

Re-flashing often returns 'Upgrade failed' on these boxes. Boot it with no internet, let it load for a minute, then turn on your phone's hotspot; one owner drove 150 km without the loop that way.

If none of these fixes work

Try every free fix above first. Each of these needs a car whose screen already runs wired CarPlay or Android Auto. We have not tested them: check the seller's compatibility list for your car and head unit, and that the listing shows the exact model named here, before you buy.

  • Wireless CarPlay / Android Auto adapter (Carlinkit Mini Ultra 3)

    If you only use the box to get CarPlay or Android Auto without a cable, a plain wireless adapter has no Android system to update, overheat or crash.

    AliExpress

  • Replacement AI box (Carlinkit, Android 13, SM6225)

    If the box is out of warranty and still fails after the fixes above, another Carlinkit box keeps your apps on the car screen. It needs wired CarPlay or Android Auto in the car. Pick the NA variant for North American cars, EAU elsewhere.

    AliExpress

  • Carlinkit TBox Ultra (Android 15)

    If an older box is too slow for the apps you run: the TBox Ultra is Carlinkit's Android 15 box, with an SM6350 chip. Check that the variant on the listing supports your car's protocol before buying.

    AliExpress

  • Replacement from another maker (Ottocast P3 Pro)

    If you would rather switch brands, Ottocast's P3 Pro runs Android 13 and has HDMI out. It needs the connection protocol Ottocast lists for your car. The listing opens on a cheaper Mini adapter: select the P3 Pro option and check the picture and name before you pay.

    AliExpress

Affiliate links: we may earn a commission at no extra cost to you. Disclosure.

Did this work for you?

Tell us which fix worked (or didn't), with your box, firmware date and car. Reports are how fixes get confirmed and re-ranked.

Send a report

Changelog

  • Last reviewed against new community reports:
  • Confirmed by 11 community reports on Carlinkit TBox Plus.
  • Fixed in firmware 2026-01-07.
  • Page updated:

"Confirmed" means a community member reported that the fix worked on their unit. We have not tested it on our own hardware. How we verify.

Evidence behind these counts (3 cases)

One row per case: a device, a symptom and a fix, merged from owner reports. An owner counts once per fix. Reports with no outcome yet are not counted. Forum and chat message references are kept on file but not published, to protect owners' privacy; public Reddit and YouTube sources are linked.

CaseConfirmed onResultSource
case-1661Carlinkit TBox Plus8 worked, 2 did notOwner reviews, 8 messages
case-1662Carlinkit TBox Plus (A13)1 workedOwner discussion threads, 2 messages
case-1663Model not stated2 workedOwner discussion threads, 2 messages