Skip to content
AI Box Fix

Firmware & recoveryReviewed

Factory Reset an Ottocast Wireless CarPlay Adapter

Ottocast adapter lost Bluetooth or won't pair? Reset it at 192.168.1.101 with Restore factory settings; Play2Video: the button behind the vent.

Illustration: Ottocast Picasou 2 on a dashboard on a rainy evening

Quick answer

To factory reset an Ottocast wireless CarPlay adapter, turn the phone's Bluetooth off, join the adapter's Wi-Fi, open 192.168.1.101 in the phone's browser and tap Restore factory settings; that worked for 2 of 3 owners who reported back. For a Play2Video that blinks and will not connect, one owner reset it with the button behind the vent.

Before you start

  • The adapter powered: plugged into the car's USB port with the car on
  • The adapter's Wi-Fi password, from its manual
  • A phone with a web browser
  • Accepting that the reset clears the adapter's own settings, so the phone has to be paired again

Time: about 10 minutes. Tools: phone browser.

Applies to

Devices
  • Any Android AI box
Connection to the car
CarPlay and Android Auto
Highest risk on this page
Advanced

What this guide covers

Ottocast’s screenless wireless adapters, the dongles that turn wired CarPlay into wireless, have no screen or menu of their own. Their settings, including the factory reset, live on a page the adapter serves over its own Wi-Fi network, which you open in your phone’s browser. Ottocast’s own FAQ gives 192.168.1.101 as that page’s address.

Owners reset these adapters when they stop pairing or misbehave: one owner’s adapter had stopped putting out Bluetooth altogether. If the adapter lights up but CarPlay never starts, check the cable and the plug first in wireless CarPlay adapter lights up but CarPlay never starts: those causes are more common, and checking them erases nothing.

If you have a full Android AI box such as an Ottocast Picasou, this is the wrong page: those boxes reset from their Settings app or a reset hole, as in factory reset an AI box when you can’t reach Settings.

Steps

Reset from the settings page at 192.168.1.101

  • Advanced
  • Time: 5–10 minutes
  • Worked for 2 of 3 reports

Warranty warning: this uses developer or engineering access. Follow the undo steps afterwards; some sellers refuse warranty claims on units with debugging left enabled.

  1. Plug the adapter into the car’s USB port and turn the car on.
  2. On the phone, turn Bluetooth off.
  3. In the phone’s Wi-Fi settings, forget the adapter’s network, then join it again. The password is in the adapter’s manual (88888888 on the adapter in the steps these owners followed).
  4. Open the phone’s browser and go to 192.168.1.101.
  5. Tap Restore factory settings and confirm with OK.
  6. While you are on the page, check whether a firmware update is offered.
  7. Turn Bluetooth back on and pair the phone with the adapter again, as you did the first time.

Two owners reported that the reset worked. One had an adapter that was no longer putting out Bluetooth: after logging in to the page, they ran the factory reset, then took the update the page offered, and the adapter worked again. The other followed the same steps and wrote that it worked.

It did not help a third owner. Their adapter had updated successfully, but afterwards CarPlay would not launch and the light stayed solid red; the reset changed nothing, and they reported no fix. A fault that starts right after an update may need the maker rather than a reset; see the troubleshooting section below.

Ottocast Play2Video: reset with the button behind the vent

  • Low risk
  • Time: 2 minutes
  • Worked for 1 of 1 report
  1. Leave the adapter plugged in and powered.
  2. Look through the vent on the adapter’s casing for a small button.
  3. Press it twice quickly.
  4. Press it a third time and hold it.
  5. Release when the blue light starts again, then reconnect the phone.

One owner reported this, answering another owner whose Play2Video kept blinking and would not connect to the car: they had a similar issue, and the two quick presses and one long press brought it back. They added that holding the button down may also reset it, but did not say they had tried that.

Verify it worked

  1. After the reset, the adapter’s Wi-Fi network and its settings page are back at their defaults. Join the network again and open 192.168.1.101 to check that the page loads.
  2. If your phone still lists the adapter under Bluetooth or saved Wi-Fi networks, remove both entries, then pair it as a new device.
  3. Start the car and wait for CarPlay on the car screen. If the fault you reset for was missing Bluetooth or failed pairing, make one call and play some audio to check it is gone.

Undo / rollback

A factory reset cannot be undone. What it clears is the adapter’s own settings and pairings, not your phone or the car, so the way back is to set the adapter up again as on the first day: pair it, then change any setting you had changed on its page.

If the reset was meant to cure a fault that started with a firmware update, the reset does not take the update back. No owner in these reports found a rollback for these adapters; ask Ottocast support.

Troubleshooting this guide

The settings page will not open. Check that the phone is still joined to the adapter’s Wi-Fi and that Bluetooth is off. From an Android phone, the page sometimes refuses to load; the Wi-Fi Direct route in update an Ottocast wireless adapter’s firmware from your phone is what got other owners onto the adapter’s pages, and the same guide lists 192.168.50.2 for adapters that do not answer at 192.168.1.101.

The light stays solid red after an update. One owner had this, and the reset did not bring CarPlay back. Write to Ottocast at [email protected] or through its contact page with the model on the adapter’s label, the version you updated to and what the light does. How to report a bug has a checklist of what to send.

The adapter resets but still drops the connection. The fault is not in its settings. Work through wireless CarPlay adapter keeps disconnecting, which covers the cable, power from two USB ports and firmware.

Nothing works. If the adapter neither opens its page nor reacts to a reset, it may have failed. Contact Ottocast support first; if you are deciding what to buy instead, start here.

What owners said

“There is a little button that you can see through the vent. Give it 2 quick presses and a third long press. Hold down until your blue light starts again. This worked for me.”
Worked: Reset button behind the vent
Owner, Oct 2024YouTube video
“My device was not outputting Bluetooth. After logging in I did a factory reset and got an update; now I am right as rain.”
Worked: Factory reset at 192.168.1.101, then update
Owner, Oct 2023YouTube video
“After a successful update Apple CarPlay isn't launching and the device has a solid red light. I then reset to factory settings but it is still not working.”
Did not help: Factory reset after an update
Owner, Oct 2024YouTube video

Quotes are translated where needed and shortened ([…]); names are removed. Full counts are in the evidence table below.

Questions owners ask

Does the factory reset also update the adapter?

No. The reset only returns the adapter to its factory settings. One owner whose adapter had stopped putting out Bluetooth reset it and then installed an update from the same page, and that pair of steps fixed it. The update has its own guide on this site.

What if the adapter shows a solid red light after an update?

One owner had that: after an update that reported success, CarPlay no longer launched and the light stayed solid red. A factory reset did not help, and no fix was reported. Contact Ottocast support with the adapter model and the version you installed.

Where is the reset button on an Ottocast Play2Video?

One owner found a small button that can be seen through the vent on the casing. Two quick presses and a third long press, held until the blue light starts again, reset the adapter for them.

Did this work for you?

Tell us which fix worked (or didn't), with your box, firmware date and car. Reports are how fixes get confirmed and re-ranked.

Send a report

Changelog

  • Last reviewed against new community reports:
  • Confirmed by 3 community reports.
  • Page updated:

"Confirmed" means a community member reported that the fix worked on their unit. We have not tested it on our own hardware. How we verify.

Evidence behind these counts (2 cases)

One row per case: a device, a symptom and a fix, merged from owner reports. An owner counts once per fix. Reports with no outcome yet are not counted. Forum and chat message references are kept on file but not published, to protect owners' privacy; public Reddit and YouTube sources are linked.

CaseConfirmed onResultSource
case-1836Model not stated2 worked, 1 did notOwner reviews, 2 messages
YouTube video
YouTube video
YouTube video
case-1837Model not stated1 workedOwner reviews, 1 message
YouTube video